Pressure-Treated Lumber Sizes

Common treated board and post dimensions, including 2x and 4x sizes and 5/4 deck boards, and how wet treated lumber can differ from the dry reference size.

Pressure-Treated Lumber Sizes

Pressure-treated dimension lumber uses the same nominal names and the same typical dressed sizes as untreated softwood. A treated 2x4 is still a 2x4, with a usual dry size of about 1.5 × 3.5 inches. A treated 4x4 post is about 3.5 × 3.5 inches. The treatment changes decay resistance, not the size system.

One practical difference: treated lumber is often still wet when it is sold. A wet board can measure a little thicker or wider than the dry reference size, then shrink as it dries. If a tight fit matters, measure the pieces you have and allow for drying movement.

Common Treated Sizes

Nominal size Typical dry actual size Metric (approx.) Typical outdoor use
2x4 1.5 × 3.5 in 38 × 89 mm Rails, short framing, some fence parts
2x6 1.5 × 5.5 in 38 × 140 mm Deck joists or rails where the design calls for 2x6
2x8 1.5 × 7.25 in 38 × 184 mm Joists and beams, when specified
2x10 1.5 × 9.25 in 38 × 235 mm Longer joists and stairs, when specified
2x12 1.5 × 11.25 in 38 × 286 mm Headers, stringers, and heavier framing, when specified
4x4 3.5 × 3.5 in 89 × 89 mm Fence posts, mailbox posts, light deck posts
4x6 3.5 × 5.5 in 89 × 140 mm Posts and beams
6x6 5.5 × 5.5 in 140 × 140 mm Heavier deck or pergola posts
5/4 x 6 deck board Typically 1 × 5.5 in 25 × 140 mm Decking; some boards are slightly narrower

These actual sizes match the standard softwood dimensions on the lumber size chart. Lengths are commonly 8, 10, 12, and 16 feet; posts and decking are also sold in other lengths depending on the yard.

Advertisement

Ground Contact Versus Above Ground

Size does not tell you whether a board is rated for ground contact. That information is on the end tag or ink stamp, which should state the preservative system and the use category (for example above-ground or ground-contact). A 4x4 post set in soil needs a product rated for that use; a 2x6 used as a deck board may be an above-ground product. This page is about dimensions, not a substitute for the rating on the stamp.

Why Treated Boards Can Feel “Oversized”

Because many treated boards are sold wet, a freshly purchased 2x6 or 4x4 can measure a little more than 1.5 × 5.5 or 3.5 × 3.5 inches. As the wood dries, it usually moves closer to the familiar dry dimensions and may also warp or check. Fasten decks and fences with that movement in mind, and avoid assuming that two boards bought months apart will be identical in width.

Sizes here are typical U.S. softwood references for pressure-treated boards and posts. Treatment brand, retention, use category, and species vary. This is not a span table, fastener schedule, or ground-contact specification. Use the product stamp and the project design for those decisions.

Pressure-Treated Size FAQ

Is a pressure-treated 2x4 the same size as an untreated 2x4?

Yes. The nominal name and the typical dry dressed size are the same: about 1.5 × 3.5 inches. Wet treated lumber can measure slightly larger until it dries.

What is the actual size of a 4x4 pressure-treated post?

About 3.5 × 3.5 inches (89 × 89 mm) when dry. A 6x6 is about 5.5 × 5.5 inches (140 × 140 mm).

What is the actual size of a 5/4 deck board?

Nominal size is 1.25 × 6 inches. A typical dressed board is about 1 × 5.5 inches. Measure the boards you buy, because some lines are slightly narrower.

Does “pressure treated” mean the board can go in the ground?

Not by itself. Look for a ground-contact rating on the stamp or end tag. Size alone does not tell you the use category.

Advertisement